S2/S3 Hose Assembly The fire-rated hose assembly has a braided stainless steel outer band with EPDM inner tube and brass or steel fittings. Hose is tested to 450 PSI and covered by an exclusive 12-month hose and labor warranty. Notes: 1/2"-1" hoses use brass fittings; 1 1/4"-2" hoses use steel fittings.

Clear Vinyl Condensate Hose Clear Vinyl Condensate Hose, 3/4” I.D. with appropriate M.P.T. sized nylon fittings. To be used when 2’ differential “P” trap is required.

Clear Vinyl Condensate Hose Clear Vinyl Condensate Hose, 3/4” I.D. with appropriate M.P.T. sized nylon fittings. To be used when 2’ differential “P” trap is required and connected to ball type blowdown valve.

Pressure/Temperature Test Ports with Superseal P/T plug features dual durometer EDPM (Nordel) internal seals and dual seal safety cap, with retaining strap. Single P/T Port, P/T Port w/ P/T extender, and Dual XL Ports for Kits A & B. Use Pressure/Temp Port in any device with port section. Regular - Hgt. = 1-1/4”, Extended - Hgt. = 2-3/4”. Rated 1000 psig at 270°F.

Manual Air Vent has a brass body and a blowout-proof needle style valve with a side vent. The knurled/slotted top can be sealed finger tight. Rated 400 psig at 250°F.
Knurled, slotted handle manual air vent, use with any port section device. Hgt = 1-1/2”.

Stem Extender Use to extend accessories to clear 2" insullation (MPT x FPT 1/4" or 1/8"). Extends access valve, air vent, or blowdown.

Memory Stop Use for ball valve devices that do not come standard with memory stop.
Memory Stop for 1/2” - 2” Valves.

Sweat Adapter (SWT X FPT) Use in addition to nipples provided with kit for sweat connected units (1/2” - 1”).
 
Note: Must be sweated / soldered separate from hose before connecting. Not doing this voids warranty.

Hose Size Increaser Use in addition to nipples provided with kit for one size larger heat pump (1/2” - 1”) connection.
Figure A: Hose Size Increaser 1/2” hose to 3/4” connection, 3/4” hose to 1” connection
Figure B: 1” hose to 1 1/4” connection

Inverted Flare Reducing Nipple Use in addition to nipples provided with kit for one size smaller heat pump (1/2” - 1”) connection.
3/4” hose to 1/2” connection, 1” hose to 3/4” connection

Sweat Adapter (SWT X MPT) Use in lieu of nipples provided with kit for sweat connected units (1-1/4” - 2”).
 
Note: Must be sweated / soldered separate from hose before connecting. Not doing this voids warranty.

Reducing Bushing w/ Nipple Use in lieu of nipples provided with kit for connections at heat pump (1-1/4” - 2”) for one size difference.
(Either one size up or down heat pump connection size.)

Hose End Drain Valve Hose End Drain Valve is a brass ball valve with chrome-plated ball, Teflon seats, plastic handle and a 3/4" hose outlet with cap. Rated 400 psig at 250° F.

1/4" Mini-Ball Drain Valve Mini-Ball Drain Valve has a brass body plastic handle and 1/4” FPT outlet connection. Rated 400 psig at 275°F.

Extended Handle on ball valve products provides approximately 2” extra clearance for insulation.

Metal ID Tags Tempered aluminum tag with chrome plated ball chain. Mylar label with etched writable information blocks.